74ABT574CSCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ABT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 150MHz |
| Base Part Number | 74ABT574 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 7.4 ns |
| Turn On Delay Time | 3.2 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 50μA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ABT574CSCX Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). The package Tape & Reel (TR)contains it. This output is configured with Tri-State, Inverted. The trigger it is configured with uses Positive Edge. There is an electric part mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is operating at -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 74ABT series. A frequency of 200MHzshould not be exceeded by its output. There are 1 elements in it. T flip flop consumes 50μA quiescent energy. If you search by 74ABT574, you will find similar parts. The input capacitance of this JK flip flopis 5pF farads. Electronic part Surface Mountis mounted in the way. There are 20pins on it. Its clock edge trigger type is Positive Edge. The flip flop is designed with 8bits. Using 8 circuits, it is highly flexible. High efficiency requires the supply voltage to be maintained at 5V. It operates with 3 output lines. This input has 1lines in it. -32mAis set as the high level output current. In the low level output current setting, the current is set to 64mA. Ideally, the operating temperature should be below 85°C. Ideally, the operating temperature should be higher than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. It supports the maximal supply voltage of 5.5V. It is possible to achieve a frequency of 150MHz.
74ABT574CSCX Features
Tape & Reel (TR) package
74ABT series
20 pins
8 Bits
74ABT574CSCX Applications
There are a lot of ON Semiconductor 74ABT574CSCX Flip Flops applications.
- ESD performance
- Asynchronous counter
- Frequency Dividers
- Load Control
- Counters
- Individual Asynchronous Resets
- Bounce elimination switch
- Set-reset capability
- Power down protection
- Consumer
