74ABT74PW,112
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Supplier Device Package | 14-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ABT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 250MHz |
| Base Part Number | 74ABT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 2 |
| Clock Frequency | 250MHz |
| Propagation Delay | 3 ns |
| Quiescent Current | 50μA |
| Turn On Delay Time | 3 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 50μA |
| Current - Output High, Low | 15mA 20mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 4.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -15mA |
| Input Capacitance | 3pF |
| Low Level Output Current | 20mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74ABT74PW,112 Overview
The package is in the form of 14-TSSOP (0.173, 4.40mm Width). As part of the package Tube, it is embedded. Currently, the output is configured to use Differential. The trigger configured with it uses Positive Edge. There is an electric part mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. -40°C~85°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74ABTseries of FPGAs. Its output frequency should not exceed 250MHz. In total, it contains 2 elements. This process consumes 50μA quiescents. D latch belongs to the 74ABT74 family. Its input capacitance is 3pF farads. A part of the electronic system is mounted in the way of Surface Mount. There are 14pins on it. In this device, the clock edge trigger type is Positive Edge. 2bits are used in its design. Its superior flexibility is attributed to its use of 2 circuits. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It is designed with 1 output lines. It is reported that there are 1 input lines. Despite external influences, it consumes 50μAof quiescent current. -15mA is set as the high level output current. 20mA is the low level output current. Ideally, the operating temperature should be lower than 85°C. If the operating temperature is higher than -40°C, the system should operate properly. It operates with the minimal supply voltage of 4.5V. 5.5Vis its maximum supply voltage. This frequency can be achieved 250MHz.
74ABT74PW,112 Features
Tube package
74ABT series
14 pins
2 Bits
74ABT74PW,112 Applications
There are a lot of Nexperia USA Inc. 74ABT74PW,112 Flip Flops applications.
- Test & Measurement
- Shift Registers
- Pattern generators
- Bus hold
- Synchronous counter
- QML qualified product
- Load Control
- Single Down Count-Control Line
- Guaranteed simultaneous switching noise level
- Individual Asynchronous Resets
