74ABT821DB,118
| Parameters | |
|---|---|
| Type | D-Type |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Additional Feature | POWER OFF DISABLE OUTPUTS TO PERMIT LIVE INSERTION; WITH POWER-UP RESET |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ABT821 |
| JESD-30 Code | R-PDSO-G24 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Clock Frequency | 185MHz |
| Family | ABT |
| Current - Quiescent (Iq) | 250μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 32mA 64mA |
| Output Polarity | TRUE |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 10 |
| Max Propagation Delay @ V, Max CL | 6.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Propagation Delay (tpd) | 6.7 ns |
| Power Supply Current-Max (ICC) | 38mA |
| Height Seated (Max) | 2mm |
| Length | 8.2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 24-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
74ABT821DB,118 Overview
The package is in the form of 24-SSOP (0.209, 5.30mm Width). A package named Tape & Reel (TR)includes it. There is a Tri-State, Non-Invertedoutput configured with it. It is configured with a trigger that uses Positive Edge. This electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. There is D-Type type of electronic flip flop associated with this device. JK flip flop belongs to the 74ABTseries of FPGAs. This D flip flop should not have a frequency greater than 185MHz. The list contains 1 elements. As a result, it consumes 250μA quiescent current and is not affected by external forces. The number of terminations is 24. The 74ABT821 family contains this object. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the ABTfamily. This part is included in FF/Latches. Vsup reaches its maximum value at 5.5V. Normally, the supply voltage (Vsup) should be above 4.5V. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The power supply is 5V. A D flip flop with 2embedded ports is available. Additionally, it is characterized by POWER OFF DISABLE OUTPUTS TO PERMIT LIVE INSERTION; WITH POWER-UP RESET.
74ABT821DB,118 Features
Tape & Reel (TR) package
74ABT series
5V power supplies
74ABT821DB,118 Applications
There are a lot of NXP USA Inc. 74ABT821DB,118 Flip Flops applications.
- Patented noise
- CMOS Process
- Counters
- Synchronous counter
- Computers
- Storage Registers
- Balanced 24 mA output drivers
- Reduced system switching noise
- Balanced Propagation Delays
- Test & Measurement
