74ACT175SC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 236MHz |
| Base Part Number | 74ACT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Output Current | 24mA |
| Number of Bits | 4 |
| Clock Frequency | 236MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT175SC Overview
The package is in the form of 16-SOIC (0.154, 3.90mm Width). It is included in the package Tube. As configured, the output uses Differential. There is a trigger configured with Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is operating at -40°C~85°C TA. This D latch has the type D-Type. It is a type of FPGA belonging to the 74ACT series. Its output frequency should not exceed 236MHz. A total of 1 elements are present. As a result, it consumes 40μA quiescent current. D latch belongs to the 74ACT175 family. A 4.5pFfarad input capacitance is provided by this T flip flop. It is mounted by the way of Surface Mount. The 16pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is designed with 4bits. To achieve this superior flexibility, 4 circuits are used. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. It operates with 2 output lines. This input has 1lines. -24mAis set as the high level output current. In the low level output current setting, 24mAis used. Ideally, the operating temperature should be below 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. It is capable of supporting a maximum supply voltage of 5.5V. We are able to achieve a frequency of 236MHz.
74ACT175SC Features
Tube package
74ACT series
16 pins
4 Bits
74ACT175SC Applications
There are a lot of ON Semiconductor 74ACT175SC Flip Flops applications.
- Instrumentation
- Modulo – n – counter
- Count Modes
- Common Clocks
- Patented noise
- Computing
- Frequency Dividers
- CMOS Process
- Registers
- Event Detectors
