74AHC377D,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 3.9 ns |
| Turn On Delay Time | 8 ns |
| Family | AHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74AHC377D,112 Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. It is contained within the Tubepackage. As configured, the output uses Non-Inverted. The trigger configured with it uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~5.5V. The operating temperature is -40°C~125°C TA. This electronic flip flop is of type D-Type. In terms of FPGAs, it belongs to the 74AHC series. There should be no greater frequency than 120MHzon its output. A total of 1 elements are present. During its operation, it consumes 4μA quiescent energy. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 74AHC377, you will find similar parts. A voltage of 5V is used to power it. Input capacitance of this device is 3pF farads. This D flip flop belongs to the family of AHC. There is an electronic part mounted in the way of Surface Mount. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. 8bits are used in its design. For normal operation, the supply voltage (Vsup) should be above 2V. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There are 8 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply.
74AHC377D,112 Features
Tube package
74AHC series
20 pins
8 Bits
74AHC377D,112 Applications
There are a lot of Nexperia USA Inc. 74AHC377D,112 Flip Flops applications.
- Asynchronous counter
- Frequency Dividers
- Buffer registers
- Common Clocks
- Frequency division
- Control circuits
- Guaranteed simultaneous switching noise level
- Individual Asynchronous Resets
- EMI reduction circuitry
- Latch-up performance
