74AHC377PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74AHC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 10.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 5.6 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
74AHC377PW-Q100J Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). D flip flop is included in the Tape & Reel (TR)package. There is a Non-Invertedoutput configured with it. Positive Edgeis the trigger it is configured with. Surface Mountmounts this electrical part. The JK flip flop operates at 2V~5.5Vvolts. -40°C~125°C TAis the operating temperature. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74AHC series. You should not exceed 120MHzin its output frequency. There are 1 elements in it. The number of terminations is 20. You can search similar parts based on 74AHC377. The power source is powered by 5V. A JK flip flop with a 3pFfarad input capacitance is used here. A device of this type belongs to the family of AHC/VHC/H/U/V. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 20pins on it. The clock edge trigger type for this device is Positive Edge. There are 8bits in its design. Normally, the supply voltage (Vsup) should be kept above 2V. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. The number of input lines is 8. There is 4μA quiescent current consumption by it.
74AHC377PW-Q100J Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
74AHC377PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHC377PW-Q100J Flip Flops applications.
- Single Up Count-Control Line
- ESD protection
- Frequency Divider circuits
- Shift Registers
- Buffered Clock
- Latch-up performance
- Load Control
- Computers
- Counters
- Shift registers
