74F112PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | JK Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 105MHz |
| Base Part Number | 74F112 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 2 |
| Clock Frequency | 105MHz |
| Propagation Delay | 6.5 ns |
| Turn On Delay Time | 5 ns |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 19mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 6.5ns @ 5V, 50pF |
| Trigger Type | Negative Edge |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Negative Edge |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
74F112PC Overview
It is packaged in the way of 16-DIP (0.300, 7.62mm). D flip flop is included in the Tubepackage. T flip flop is configured with an output of Differential. JK flip flop uses Negative Edgeas the trigger. Through Holeis positioned in the way of this electronic part. A voltage of 4.5V~5.5Vis required for its operation. It is at 0°C~70°C TAdegrees Celsius that the system is operating. This electronic flip flop is of type JK Type. The FPGA belongs to the 74F series. It should not exceed 105MHzin terms of its output frequency. In total, there are 2 elements. It consumes 19mA of quiescent D latch belongs to the 74F112 family. There is an electronic part mounted in the way of Through Hole. A total of 16pins are provided on this board. A Negative Edgeclock edge trigger is used in this device. This flip flop is designed with 2 Bits. Despite its superior flexibility, it relies on 2 circuits to achieve it. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. It operates with 3 output lines. There are 2 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. There is -1mA output current at the high level. There is 20mA output current at the low level. There should be a temperature below 70°Cduring operation. A temperature above 0°Cshould be used for the operation. The minimal supply voltage is 4.5V. It supports the maximal supply voltage of 5.5V. This frequency can be achieved 105MHz.
74F112PC Features
Tube package
74F series
16 pins
2 Bits
74F112PC Applications
There are a lot of ON Semiconductor 74F112PC Flip Flops applications.
- ESCC
- Synchronous counter
- Consumer
- Count Modes
- Test & Measurement
- Reduced system switching noise
- EMI reduction circuitry
- Dynamic threshold performance
- Safety Clamp
- ESD protection
