74F374SCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 140MHz |
| Base Part Number | 74F374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 140MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 86mA |
| Current - Output High, Low | 3mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -3mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F374SCX Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. The Tape & Reel (TR)package contains it. The output it is configured with uses Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. Surface Mountis positioned in the way of this electronic part. A voltage of 4.5V~5.5Vis required for its operation. A temperature of 0°C~70°C TAis used in the operation. This electronic flip flop is of type D-Type. JK flip flop is a part of the 74Fseries of FPGAs. You should not exceed 140MHzin its output frequency. In total, it contains 1 elements. This process consumes 86mA quiescents. The object belongs to the 74F374 family. Electronic part Surface Mountis mounted in the way. This board is designed with 20pins on it. It has a clock edge trigger type of Positive Edge. Flip flops designed with 8bits are used in this part. 8 circuits are used to achieve its superior flexibility. For high efficiency, the supply voltage should be set to 5V. There are no output lines on the JK flip flop. It has 8lines. There is -3mA output current at the high level. 24mAis set as the low level output current. It is recommended that the operating temperature be below 70°C. If the operating temperature is higher than 0°C, the system should operate properly. Initially, it requires a voltage of 4.5V as the minimum supply voltage. There is a maximum voltage support of 5.5V. It is possible to achieve 140MHz frequencies.
74F374SCX Features
Tape & Reel (TR) package
74F series
20 pins
8 Bits
74F374SCX Applications
There are a lot of ON Semiconductor 74F374SCX Flip Flops applications.
- Balanced 24 mA output drivers
- EMI reduction circuitry
- Divide a clock signal by 2 or 4
- Bus hold
- Modulo – n – counter
- Balanced Propagation Delays
- Instrumentation
- ESD protection
- Shift Registers
- Pattern generators
