74F377SJ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 130MHz |
| Base Part Number | 74F377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 7 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 48mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 7ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F377SJ Overview
It is embeded in 20-SOIC (0.209, 5.30mm Width) case. Package Tubeembeds it. The output it is configured with uses Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountis in the way of this electric part. A 4.5V~5.5Vsupply voltage is required for it to operate. It is operating at 0°C~70°C TA. There is D-Type type of electronic flip flop associated with this device. In terms of FPGAs, it belongs to the 74F series. There should be no greater frequency than 130MHzon its output. In total, it contains 1 elements. During its operation, it consumes 48mA quiescent energy. JK flip flop belongs to 74F377 family. Surface Mount mounts this electronic component. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The design is based on 8bits. Despite its superior flexibility, it relies on 1 circuits to achieve it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. It has 8lines. -1mAis set as the high level output current. Low level output current is set to 20mA. A temperature below 70°Cis recommended for operation. Operating temperatures should be above 0°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. It supports the maximal supply voltage of 5.5V. It is possible to achieve 130MHz frequencies.
74F377SJ Features
Tube package
74F series
20 pins
8 Bits
74F377SJ Applications
There are a lot of ON Semiconductor 74F377SJ Flip Flops applications.
- Single Down Count-Control Line
- Cold spare funcion
- Safety Clamp
- Individual Asynchronous Resets
- Consumer
- High Performance Logic for test systems
- Instrumentation
- Functionally equivalent to the MC10/100EL29
- Balanced Propagation Delays
- Event Detectors
