74F574SJX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 100MHz |
| Base Part Number | 74F574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 5.3 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 86mA |
| Current - Output High, Low | 3mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -3mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F574SJX Overview
It is packaged in the way of 20-SOIC (0.209, 5.30mm Width). There is an embedded version in the package Tape & Reel (TR). The output it is configured with uses Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. It is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. It is operating at 0°C~70°C TA. Logic flip flops of this type are classified as D-Type. It is a type of FPGA belonging to the 74F series. A frequency of 100MHzshould not be exceeded by its output. In total, it contains 1 elements. It consumes 86mA of quiescent You can search similar parts based on 74F574. It is mounted in the way of Surface Mount. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. Flip flops designed with 8bits are used in this part. Due to its superior flexibility, it uses 8 circuits. If high efficiency is desired, the supply voltage should be kept at 5V. To operate, the chip has a total of 3 output lines. There are 1 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. In this case, the high level output current is set to -3mA. A 24mAvalue is set for low-level output current. A temperature below 70°Cis recommended for operation. Temperatures above 0°Cshould be used. The system operates with a minimum supply voltage of 4.5V. There is a maximum voltage support of 5.5V. It is possible to achieve a frequency of 100MHz.
74F574SJX Features
Tape & Reel (TR) package
74F series
20 pins
8 Bits
74F574SJX Applications
There are a lot of ON Semiconductor 74F574SJX Flip Flops applications.
- Communications
- Functionally equivalent to the MC10/100EL29
- Balanced Propagation Delays
- Dynamic threshold performance
- Single Down Count-Control Line
- Memory
- Patented noise
- Buffer registers
- Memory
- Digital electronics systems
