74F825SPC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 24-DIP (0.300, 7.62mm) |
| Number of Pins | 24 |
| Supplier Device Package | 24-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 160MHz |
| Base Part Number | 74F825 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 9.5 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 90mA |
| Current - Output High, Low | 3mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -3mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
74F825SPC Overview
24-DIP (0.300, 7.62mm)is the way it is packaged. There is an embedded version in the package Tube. T flip flop uses Tri-State, Non-Invertedas the output. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Through Hole. A voltage of 4.5V~5.5Vis used as the supply voltage. The operating temperature is 0°C~70°C TA. This electronic flip flop is of type D-Type. The FPGA belongs to the 74F series. Its output frequency should not exceed 160MHz. D latch consists of 1 elements. There is a consumption of 90mAof quiescent energy. You can search similar parts based on 74F825. Electronic part Through Holeis mounted in the way. With its 24pins, it is designed to work with most electronic flip flops. The clock edge trigger type for this device is Positive Edge. It is designed with 8bits. In order to achieve its superior flexibility, 8 circuits are used. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There are 1 output lines in this JK flip flop. It has 2lines. It is set to -3mAfor the high level output current. It is set to 24mAfor low level output current. It is recommended that the operating temperature be lower than 70°C. The operating temperature should be higher than 0°C. Initially, it requires a voltage of 4.5V as the minimum supply voltage. It is capable of supporting a maximum supply voltage of 5.5V. This can be achieved at a frequency of 160MHz.
74F825SPC Features
Tube package
74F series
24 pins
8 Bits
74F825SPC Applications
There are a lot of ON Semiconductor 74F825SPC Flip Flops applications.
- Frequency division
- Cold spare funcion
- Frequency Dividers
- Bus hold
- Count Modes
- Digital electronics systems
- Instrumentation
- Reduced system switching noise
- Bounce elimination switch
- Shift Registers
