74FCT162823ATPAG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TFSOP |
| Number of Pins | 56 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 20 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 23 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 14mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823ATPAG Overview
It is embeded in TFSOP case. D latch consists of 2 elements. A total of 56 terminations have been made. The D flip flop is powered by a voltage of 5V . Electronic devices of this type belong to the FCTfamily. The electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 56. Its clock edge trigger type is Positive Edge. The part is included in FF/Latches. This flip flop is designed with 18 Bits. The power supply is 5V. There are 2 ports embedded in the flip flops. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. This D latch consumes 500μA quiescent current at all. High level output current is set to -24mA. Low level output current is set to 24mA. It is recommended that the operating temperature be lower than 85°C. Ideally, the operating temperature should be higher than -40°C. Initially, it requires a voltage of 4.5V as the minimum supply voltage. A maximum voltage of 5.5V can be provided by it. It uses a logic IC with a BUS DRIVER value. A total of 2 functions are available on the T flip flop. With 56 pins, it is equipped with a low power consumption.
74FCT162823ATPAG Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823ATPAG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823ATPAG Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- CMOS Process
- Set-reset capability
- Memory
- ATE
- Shift registers
- Count Modes
- Divide a clock signal by 2 or 4
- Memory
- Balanced 24 mA output drivers
