74FCT162823CTPVG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 56 |
| Weight | 694.790113mg |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 8 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 12.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 115mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Height | 2.3mm |
| Length | 18.4mm |
| Width | 7.5mm |
| Thickness | 2.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823CTPVG Overview
It is embeded in SSOP case. A total of 2 elements are present. There are 56 terminations,Power is supplied from a voltage of 5V volts. A device of this type belongs to the family of FCT. In this case, the electronic component is mounted in the way of Surface Mount. This board has 56 pins. This device exhibits a clock edge trigger type of Positive Edge. It is included in FF/Latches. This flip flop is designed with 18 Bits. The D latch runs on a voltage of 5V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. As a result, it consumes 500μA of quiescent current without being affected by external factors. It is also characterized by WITH CLEAR AND CLOCK ENABLE. A high level output current of -24mAis set. It is set to 115mAfor the low level output current. Ideally, the operating temperature should be below 85°C. The operating temperature should be higher than -40°C. It operates with the minimal supply voltage of 4.5V. 5.5Vis its maximum supply voltage. BUS DRIVERis the logic IC it uses. There are 2 functions available on this T flip flop. This device is equipped with a pin count of 56.
74FCT162823CTPVG Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823CTPVG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823CTPVG Flip Flops applications.
- Data Synchronizers
- Synchronous counter
- ESD performance
- Load Control
- Latch
- Dynamic threshold performance
- Digital electronics systems
- Bounce elimination switch
- Storage registers
- Parallel data storage
