74FCT16374ETPVG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 48 |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NS |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 3.7 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 4.4 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 32mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 15.9mm |
| Width | 7.5mm |
| Thickness | 2.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT16374ETPVG Overview
As a result, it is packaged as SSOP. In total, it contains 2 elements. A total of 48 terminations have been made. The power supply voltage is 5V. A device of this type belongs to the family of FCT. This electronic part is mounted in the way of Surface Mount. It is designed with 48 pins. It has a clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. There are 16bits in this flip flop. The D latch runs on a voltage of 5V volts. The flip flop has 2embedded ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. 500μAquiescent current consumed. There is also a characteristic of POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NS. A high level output current of -32mAis set. There is no low level output current set at 32mA. A temperature below 85°Cis recommended for operation. The operating temperature should be higher than -40°C. The system operates with a minimum supply voltage of 4.5V. The maximum supply voltage supported by the flip flop is 5.5V. There is a logic IC BUS DRIVER used in the D flip flop. There are 2 functions available on the JK flip flop. 48pins are available on this JK flip flop.
74FCT16374ETPVG Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT16374ETPVG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT16374ETPVG Flip Flops applications.
- Data storage
- Guaranteed simultaneous switching noise level
- Patented noise
- Set-reset capability
- Single Up Count-Control Line
- Test & Measurement
- ESD performance
- Data Synchronizers
- Safety Clamp
- Latch-up performance
