74FCT374CTQG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Height | 1.47mm |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT374CTQG8 Overview
The item is packaged in SSOPcases. A total of 1elements are contained within it. Currently, there are 20 terminations. A voltage of 5V is used as the power supply for this D latch. A device of this type belongs to the family of FCT. In this case, the electronic component is mounted in the way of Surface Mount. The 20pins are designed into the board. Its clock edge trigger type is Positive Edge. The part is included in FF/Latches. 8bits are used in its design. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. A D flip flop with 2embedded ports is available. In order to ensure high efficiency, the supply voltage should remain at 5V. Quiescent current is consumed by the D latch in the amount of 1mA. -15mAis the output current at high level. In the low level output current setting, 15mAis used. It is recommended that the operating temperature be below 85°C. The operating temperature should be higher than -40°C. In order for it to operate, a supply voltage of 4.75Vis required. There is a maximum voltage support of 5.25V. The logic IC it uses is BUS DRIVER. The T flip flop is equipped with 1functions . 20pins are provided on the D latch.
74FCT374CTQG8 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT374CTQG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT374CTQG8 Flip Flops applications.
- ESCC
- EMI reduction circuitry
- Frequency Dividers
- Latch
- Storage registers
- Bounce elimination switch
- Registers
- Differential Individual
- Control circuits
- ATE
