74HC173D,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SO |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 95MHz |
| Base Part Number | 74HC173 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 4 |
| Clock Frequency | 95MHz |
| Propagation Delay | 17 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 16 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Number of Inputs | 4 |
| Current - Output High, Low | 7.8mA 7.8mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -7.8mA |
| Input Capacitance | 3.5pF |
| Low Level Output Current | 7.8mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC173D,653 Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. D flip flop is embedded in the Tape & Reel (TR) package. Tri-State, Non-Invertedis the output configured for it. In the configuration of the trigger, Positive Edgeis used. Surface Mountis in the way of this electric part. With a supply voltage of 2V~6V volts, it operates. In this case, the operating temperature is -40°C~125°C TA. It belongs to the type D-Typeof flip flops. It is a type of FPGA belonging to the 74HC series. A frequency of 95MHzshould not be exceeded by its output. The element count is 1 . It consumes 4μA of quiescent The object belongs to the 74HC173 family. There is 3.5pF input capacitance for this T flip flop. The electronic part is mounted in the way of Surface Mount. This board has 16 pins. Its clock edge trigger type is Positive Edge. The flip flop is designed with 4bits. The superior flexibility of this product is achieved by using 1 circuits. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. The JK flip flop is with 4 output lines to operate. This input has 4lines. This D latch consumes 8μA quiescent current at all. -7.8mA is set as the high level output current. Low level output current is set to 7.8mA. Operating temperatures should be lower than 125°C. A temperature above -40°Cshould be used for the operation. The minimum voltage required for operation is 2V. It supports a maximum supply voltage of 6V volts. It is possible to achieve 95MHz frequencies. A total of 4inputs are used.
74HC173D,653 Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
74HC173D,653 Applications
There are a lot of Nexperia USA Inc. 74HC173D,653 Flip Flops applications.
- Event Detectors
- Single Up Count-Control Line
- Memory
- Storage registers
- Shift Registers
- Guaranteed simultaneous switching noise level
- Memory
- Common Clocks
- Registers
- Synchronous counter
