74HC174DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 107MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 6 |
| fmax-Min | 20 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74HC174DB,118 Overview
16-SSOP (0.209, 5.30mm Width)is the way it is packaged. D flip flop is included in the Tape & Reel (TR)package. This output is configured with Non-Inverted. There is a trigger configured with Positive Edge. Surface Mountis in the way of this electric part. With a supply voltage of 2V~6V volts, it operates. It is operating at -40°C~125°C TA. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74HC series. This D flip flop should not have a frequency greater than 107MHz. D latch consists of 1 elements. This process consumes 8μA quiescents. Terminations are 16. It is a member of the 74HC174 family. An input voltage of 5Vpowers the D latch. JK flip flop input capacitance is 3.5pF farads. The electronic device belongs to the HC/UHfamily. It is mounted by the way of Surface Mount. Basically, it is designed with a set of 16 pins. A Positive Edgeclock edge trigger is used in this device. The design is based on 6bits. It reaches the maximum supply voltage (Vsup) at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. It has 6lines.
74HC174DB,118 Features
Tape & Reel (TR) package
74HC series
16 pins
6 Bits
74HC174DB,118 Applications
There are a lot of Nexperia USA Inc. 74HC174DB,118 Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Pattern generators
- Dynamic threshold performance
- Computers
- Registers
- Automotive
- Computing
- Single Up Count-Control Line
- Power down protection
- Frequency Divider circuits
