74HC273BQ-Q100X
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-VFQFN Exposed Pad |
| Number of Pins | 20 |
| Supplier Device Package | 20-DHVQFN (4.5x2.5) |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 122MHz |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Clock Frequency | 122MHz |
| Propagation Delay | 26 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 26 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | 5.2mA |
| Input Capacitance | 3.5pF |
| Low Level Output Current | 5.2mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
74HC273BQ-Q100X Overview
It is embeded in 20-VFQFN Exposed Pad case. The package Tape & Reel (TR)contains it. T flip flop is configured with an output of Non-Inverted. This trigger is configured to use Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. A temperature of -40°C~125°C TAis used in the operation. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. It should not exceed 122MHzin terms of its output frequency. D latch consists of 1 elements. There is a consumption of 8μAof quiescent energy. The 74HC273family includes it. JK flip flop input capacitance is 3.5pF farads. This electronic part is mounted in the way of Surface Mount. There are 20pins on it. This device's clock edge trigger type is Positive Edge. Its superior flexibility is attributed to its use of 8 circuits. Optimal efficiency requires a supply voltage of 5V. It has 8 output lines to operate. 8input lines are available for you to choose from. As a result, it consumes 8μA of quiescent current without being affected by external factors. A 5.2mAvalue is set for the high level output current. It is set to 5.2mAfor low level output current. It is recommended that the operating temperature be lower than 125°C. If the operating temperature is higher than -40°C, the system should operate properly. Initially, it requires a voltage of 2V as the minimum supply voltage. The maximum supply voltage supported by the flip flop is 6V. It is possible to achieve a frequency of 122MHz.
74HC273BQ-Q100X Features
Tape & Reel (TR) package
74HC series
20 pins
74HC273BQ-Q100X Applications
There are a lot of Nexperia USA Inc. 74HC273BQ-Q100X Flip Flops applications.
- Shift registers
- Parallel data storage
- Bus hold
- Count Modes
- Shift Registers
- Common Clocks
- Memory
- Bounce elimination switch
- ESD performance
- Instrumentation
