74HC574DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 133MHz |
| Propagation Delay | 225 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC574DB,118 Overview
The flip flop is packaged in 20-SSOP (0.209, 5.30mm Width). D flip flop is included in the Tape & Reel (TR)package. The output it is configured with uses Tri-State, Non-Inverted. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. It is at -40°C~125°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. The 74HCseries comprises this type of FPGA. It should not exceed 133MHzin its output frequency. D latch consists of 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If you search by 74HC574, you will find similar parts. It is powered from a supply voltage of 5V. There is 3.5pF input capacitance for this T flip flop. Electronic devices of this type belong to the HC/UHfamily. There is an electronic part mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device exhibits a clock edge trigger type of Positive Edge. 8bits are used in its design. 6Vis the maximum supply voltage (Vsup). A normal operating voltage (Vsup) should remain above 2V. The D flip flop is embedded with 2ports. The supply voltage should be maintained at 5V for high efficiency. 8input lines are available for you to choose from. It consumes 8μA of quiescent current without being affected by external factors. BROADSIDE VERSION OF 374is also one of its characteristics.
74HC574DB,118 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
74HC574DB,118 Applications
There are a lot of Nexperia USA Inc. 74HC574DB,118 Flip Flops applications.
- Shift Registers
- Functionally equivalent to the MC10/100EL29
- Storage Registers
- Convert a momentary switch to a toggle switch
- ESD protection
- Guaranteed simultaneous switching noise level
- Frequency division
- Bus hold
- Asynchronous counter
- Count Modes
