74HCT173DB,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 1997 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT173 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Load Capacitance | 50pF |
| Number of Bits | 4 |
| Clock Frequency | 80MHz |
| Propagation Delay | 17 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 20 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 6mA 6mA |
| Max Propagation Delay @ V, Max CL | 40ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 4 |
| fmax-Min | 60 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74HCT173DB,112 Overview
It is packaged in the way of 16-SSOP (0.209, 5.30mm Width). D flip flop is included in the Tubepackage. The output it is configured with uses Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. The operating temperature is -40°C~125°C TA. D-Typedescribes this flip flop. The FPGA belongs to the 74HCT series. You should not exceed 80MHzin its output frequency. D latch consists of 1 elements. As a result, it consumes 4μA of quiescent current without being affected by external factors. There have been 16 terminations. If you search by 74HCT173, you will find similar parts. A voltage of 5V is used to power it. This JK flip flop has a 3.5pFfarad input capacitance. An electronic device belonging to the family HCTcan be found here. Surface Mount mounts this electronic component. A total of 16pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. There are 4bits in this flip flop. The supply voltage should be maintained at 5V for high efficiency. 4input lines are available for you to choose from. 8μAquiescent current consumed. As an additional reference, you may refer to electronic flip flop WITH HOLD MODE.
74HCT173DB,112 Features
Tube package
74HCT series
16 pins
4 Bits
74HCT173DB,112 Applications
There are a lot of Nexperia USA Inc. 74HCT173DB,112 Flip Flops applications.
- Storage Registers
- Event Detectors
- EMI reduction circuitry
- Modulo – n – counter
- Data storage
- Safety Clamp
- Count Modes
- Reduced system switching noise
- Frequency division
- Buffer registers
