74HCT174PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 69MHz |
| Propagation Delay | 18 ns |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 6 |
| fmax-Min | 20 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74HCT174PW,112 Overview
It is packaged in the way of 16-TSSOP (0.173, 4.40mm Width). A package named Tubeincludes it. Non-Invertedis the output configured for it. In the configuration of the trigger, Positive Edgeis used. Surface Mountis positioned in the way of this electronic part. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. A temperature of -40°C~125°C TAis used in the operation. This electronic flip flop is of type D-Type. FPGAs belonging to the 74HCTseries contain this type of chip. This D flip flop should not have a frequency greater than 69MHz. In total, there are 1 elements. During its operation, it consumes 8μA quiescent energy. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on 74HCT174. A voltage of 5V provides power to the D latch. JK flip flop input capacitance is 3.5pF farads. HCTis the family of this D flip flop. A part of the electronic system is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 16. A Positive Edgeclock edge trigger is used in this device. This flip flop is designed with 6 Bits. Optimal efficiency requires a supply voltage of 5V. As of now, there are 6input lines.
74HCT174PW,112 Features
Tube package
74HCT series
16 pins
6 Bits
74HCT174PW,112 Applications
There are a lot of Nexperia USA Inc. 74HCT174PW,112 Flip Flops applications.
- High Performance Logic for test systems
- Buffered Clock
- Individual Asynchronous Resets
- Frequency division
- ESD protection
- Computers
- Registers
- Safety Clamp
- Single Down Count-Control Line
- Test & Measurement
