74LVQ174SC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74LVQ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~3.6V |
| Frequency | 100MHz |
| Base Part Number | 74LVQ174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2V |
| Number of Bits | 6 |
| Clock Frequency | 100MHz |
| Propagation Delay | 16.2 ns |
| Turn On Delay Time | 9 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 12mA 12mA |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -12mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 12mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LVQ174SC Overview
As a result, it is packaged as 16-SOIC (0.154, 3.90mm Width). There is an embedded version in the package Tube. T flip flop uses Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 2V~3.6V. The operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. JK flip flop is a part of the 74LVQseries of FPGAs. It should not exceed 100MHzin terms of its output frequency. In total, it contains 1 elements. As a result, it consumes 40μA quiescent current. D latch belongs to the 74LVQ174 family. A JK flip flop with a 4.5pFfarad input capacitance is used here. This electronic part is mounted in the way of Surface Mount. The 16pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. 6bits are used in its design. Despite its superior flexibility, it relies on 7 circuits to achieve it. In order for the chip to function, it has 6output lines. This input has 3lines in it. A high level output current of -12mAis set. 12mAis set as the low level output current. It is recommended that the operating temperature be lower than 85°C. It is recommended that the operating temperature be greater than -40°C. It operates with the minimal supply voltage of 2V. It is capable of supporting a maximum supply voltage of 3.6V. A frequency of 100MHzcan be achieved.
74LVQ174SC Features
Tube package
74LVQ series
16 pins
6 Bits
74LVQ174SC Applications
There are a lot of ON Semiconductor 74LVQ174SC Flip Flops applications.
- Patented noise
- Reduced system switching noise
- Matched Rise and Fall
- Count Modes
- Frequency division
- Counters
- Divide a clock signal by 2 or 4
- Single Down Count-Control Line
- Digital electronics systems
- Asynchronous counter
