74LVTH273SJ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74LVTH |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2.7V~3.6V |
| Frequency | 150MHz |
| Base Part Number | 74LVTH273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 5.5 ns |
| Turn On Delay Time | 4.9 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 190μA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 4.9ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 3pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 7 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LVTH273SJ Overview
20-SOIC (0.209, 5.30mm Width)is the way it is packaged. Package Tubeembeds it. It is configured with Non-Invertedas an output. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2.7V~3.6V. The operating temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74LVTHseries FPGA. Its output frequency should not exceed 150MHz. In total, there are 1 elements. T flip flop consumes 190μA quiescent energy. It is a member of the 74LVTH273 family. JK flip flop input capacitance is 3pF farads. There is an electronic component mounted in the way of Surface Mount. This board has 20 pins. A Positive Edgeclock edge trigger is used in this device. There are 8bits in its design. Its superior flexibility is attributed to its use of 8 circuits. The supply voltage should be maintained at 3.3V for high efficiency. There are no output lines on the JK flip flop. Currently, there are 4 input lines present. A -32mAis set for the high level output current. There is 64mA output current at the low level. It is recommended that the operating temperature be below 85°C. Ideally, the operating temperature should be higher than -40°C. The minimum voltage required for operation is 2.7V. In this case, it supports a maximum supply voltage of 3.6V. This can be achieved at a frequency of 150MHz.
74LVTH273SJ Features
Tube package
74LVTH series
20 pins
8 Bits
74LVTH273SJ Applications
There are a lot of ON Semiconductor 74LVTH273SJ Flip Flops applications.
- Differential Individual
- Data Synchronizers
- High Performance Logic for test systems
- Circuit Design
- Functionally equivalent to the MC10/100EL29
- Data transfer
- Computing
- Load Control
- Automotive
- Convert a momentary switch to a toggle switch
