74VHC574MTC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74VHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74VHC574 |
| Function | Standard |
| Number of Outputs | 10 |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 19 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 5.6 ns |
| Family | AHC/VHC |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 900μm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74VHC574MTC Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. You can find it in the Tubepackage. T flip flop uses Tri-State, Non-Invertedas its output configuration. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. A 2V~5.5Vsupply voltage is required for it to operate. -40°C~85°C TAis the operating temperature. D-Typedescribes this flip flop. This type of FPGA is a part of the 74VHC series. It should not exceed 115MHzin terms of its output frequency. The list contains 1 elements. A total of 20 terminations have been made. The 74VHC574 family contains this object. The power supply voltage is 3.3V. A JK flip flop with a 4pFfarad input capacitance is used here. In terms of electronic devices, this device belongs to the AHC/VHCfamily of devices. Surface Mount mounts this electronic component. A total of 20pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. 8bits are used in its design. Vsup reaches its maximum value at 5.5V. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. As a result of its reliability, this D flip flop is ideally suited for RAIL. The D flip flop has no ports embedded. As a result of its output current of 8mA, it is very flexible in terms of design. A total of 2input lines have been provided. Despite external influences, it consumes 4μAof quiescent current. It is reported that there are 8 channels.
74VHC574MTC Features
Tube package
74VHC series
20 pins
8 Bits
74VHC574MTC Applications
There are a lot of ON Semiconductor 74VHC574MTC Flip Flops applications.
- Matched Rise and Fall
- Bus hold
- Count Modes
- Balanced Propagation Delays
- Data Synchronizers
- ATE
- Differential Individual
- Synchronous counter
- Shift Registers
- Frequency Divider circuits
