CD4076BNSRE4
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 4000B |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 3V~18V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | CD4076 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 3V |
| Load Capacitance | 50pF |
| Output Current | 6.8mA |
| Number of Bits | 4 |
| Clock Frequency | 16MHz |
| Propagation Delay | 600 ns |
| Turn On Delay Time | 60 ns |
| Current - Quiescent (Iq) | 20μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 6.8mA 6.8mA |
| Max Propagation Delay @ V, Max CL | 180ns @ 15V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 4 |
| fmax-Min | 8 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000Hz |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
CD4076BNSRE4 Overview
The flip flop is packaged in a case of 16-SOIC (0.209, 5.30mm Width). Package Tape & Reel (TR)embeds it. T flip flop uses Tri-State, Non-Invertedas its output configuration. This trigger is configured to use Positive Edge. There is an electric part mounted in the way of Surface Mount. A voltage of 3V~18Vis required for its operation. Temperature is set to -55°C~125°C TA. D-Typeis the type of this D latch. In terms of FPGAs, it belongs to the 4000B series. This D flip flop should not have a frequency greater than 16MHz. A total of 1elements are contained within it. There is 20μA quiescent consumption. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on CD4076. It is powered by a voltage of 5V . The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic part Surface Mountis mounted in the way. A total of 16pins are provided on this board. There is a clock edge trigger type of Positive Edgeon this device. It is included in FF/Latches. There are 4bits in its design. It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. It offers maximum design flexibility with its output current of 6.8mA. There are 4 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply.
CD4076BNSRE4 Features
Tape & Reel (TR) package
4000B series
16 pins
4 Bits
CD4076BNSRE4 Applications
There are a lot of Texas Instruments CD4076BNSRE4 Flip Flops applications.
- Balanced Propagation Delays
- Registers
- Dynamic threshold performance
- Buffer registers
- Set-reset capability
- Frequency division
- Latch-up performance
- Data transfer
- High Performance Logic for test systems
- Shift Registers
