CD74AC574M96
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 1.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 125MHz |
| Propagation Delay | 135 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.7 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74AC574M96 Overview
The flip flop is packaged in 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tape & Reel (TR) package. The output it is configured with uses Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. It operates with a supply voltage of 1.5V~5.5V. Temperature is set to -55°C~125°C TA. A flip flop of this type is classified as a D-Type. JK flip flop belongs to the 74ACseries of FPGAs. A frequency of 125MHzshould not be exceeded by its output. A total of 1 elements are present. A total of 20terminations have been recorded. D latch belongs to the 74AC574 family. A voltage of 3.3V provides power to the D latch. JK flip flop input capacitance is 10pF farads. A device of this type belongs to the family of AC. There is an electronic part that is mounted in the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. It is designed with a number of bits of 8. There is a 5.5Vmaximum supply voltage (Vsup). Using 8 circuits, it is highly flexible. Due to its reliability, this T flip flop is well suited for TR. There are 2 ports embedded in the flip flops. With an output current of 24mA, it is possible to design the device in any way you want. It has 3 output lines to operate. It consumes 8μA of quiescent current without being affected by external factors.
CD74AC574M96 Features
Tape & Reel (TR) package
74AC series
20 pins
8 Bits
CD74AC574M96 Applications
There are a lot of Texas Instruments CD74AC574M96 Flip Flops applications.
- EMI reduction circuitry
- Single Down Count-Control Line
- Storage registers
- Modulo – n – counter
- Shift Registers
- Event Detectors
- Latch-up performance
- Functionally equivalent to the MC10/100EL29
- Data Synchronizers
- Individual Asynchronous Resets
