CD74ACT175E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74ACT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 4 |
| Clock Frequency | 114MHz |
| Propagation Delay | 11.5 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.9 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74ACT175E Overview
It is embeded in 16-DIP (0.300, 7.62mm) case. The package Tubecontains it. There is a Differentialoutput configured with it. There is a trigger configured with Positive Edge. There is an electrical part that is mounted in the way of Through Hole. The JK flip flop operates at 4.5V~5.5Vvolts. The operating temperature is -55°C~125°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74ACT series. In order for it to function properly, its output frequency should not exceed 114MHz. In total, it contains 1 elements. 16terminations have occurred. The 74ACT175 family contains it. Power is supplied from a voltage of 5V volts. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family ACTcan be found here. There is an electronic part mounted in the way of Through Hole. This board has 16 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. Flip flops designed with 4bits are used in this part. The superior flexibility of this circuit is achieved by using 4 circuits. The power supply is 5V. In order to ensure high efficiency, the supply voltage should remain at 5V. With an output current of 24mA, this device offers maximum design flexibility. It consumes 8μA of quiescent current without being affected by external factors.
CD74ACT175E Features
Tube package
74ACT series
16 pins
4 Bits
5V power supplies
CD74ACT175E Applications
There are a lot of Texas Instruments CD74ACT175E Flip Flops applications.
- Common Clocks
- Pattern generators
- Storage Registers
- Instrumentation
- ESCC
- QML qualified product
- Dynamic threshold performance
- Individual Asynchronous Resets
- High Performance Logic for test systems
- Balanced Propagation Delays
