CD74ACT273PWR
| Parameters | |
|---|---|
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 85MHz |
| Propagation Delay | 13.5 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 3.4 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 13.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
CD74ACT273PWR Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). It is contained within the Tape & Reel (TR)package. The output it is configured with uses Non-Inverted. Positive Edgeis the trigger it is configured with. This electronic part is mounted in the way of Surface Mount. With a supply voltage of 4.5V~5.5V volts, it operates. In the operating environment, the temperature is -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. It belongs to the 74ACTseries of FPGAs. It should not exceed 85MHzin terms of its output frequency. In total, it contains 1 elements. Terminations are 20. The 74ACT273family includes it. A voltage of 5V is used as the power supply for this D latch. This JK flip flop has a 10pFfarad input capacitance. In this case, the D flip flop belongs to the ACTfamily. There is an electronic component mounted in the way of Surface Mount. There are 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device is part of the FF/Latchesbase part number family. The design is based on 8bits. The superior flexibility of this product is achieved by using 8 circuits. In light of its reliable performance, this T flip flop is well suited for TR. The power supply is 5V. The supply voltage should be maintained at 5V for high efficiency. Featuring the maximum design flexibility, it has an output current of 24mA . There are 4 output lines on it. Quiescent current is consumed by the D latch in the amount of 8μA.
CD74ACT273PWR Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
CD74ACT273PWR Applications
There are a lot of Texas Instruments CD74ACT273PWR Flip Flops applications.
- ESD performance
- Instrumentation
- Circuit Design
- Storage registers
- Functionally equivalent to the MC10/100EL29
- Balanced 24 mA output drivers
- EMI reduction circuitry
- Divide a clock signal by 2 or 4
- ESD protection
- Differential Individual
