CD74ACT574M96
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | Bus Driver/Transceiver |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 165 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.8 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74ACT574M96 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). It is contained within the Tape & Reel (TR)package. There is a Tri-State, Non-Invertedoutput configured with it. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates at a voltage of 4.5V~5.5V. Currently, the operating temperature is -55°C~125°C TA. The type of this D latch is D-Type. It belongs to the 74ACTseries of FPGAs. This D flip flop should not have a frequency greater than 110MHz. There are 1 elements in it. It has been determined that there have been 20 terminations. It is a member of the 74ACT574 family. A voltage of 5V is used as the power supply for this D latch. A JK flip flop with a 10pFfarad input capacitance is used here. Devices in the ACTfamily are electronic devices. Electronic part Surface Mountis mounted in the way. This board has 20 pins. In this device, the clock edge trigger type is Positive Edge. This device is part of the Bus Driver/Transceiverbase part number family. There are 8bits in its design. Using 8 circuits, it is highly flexible. In light of its reliable performance, this T flip flop is well suited for TR. It operates from 5V power supplies. This D flip flop is equipped with 0 ports. High efficiency requires the supply voltage to be maintained at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. It consumes 8μA current.
CD74ACT574M96 Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
CD74ACT574M96 Applications
There are a lot of Texas Instruments CD74ACT574M96 Flip Flops applications.
- Individual Asynchronous Resets
- Single Down Count-Control Line
- Count Modes
- Convert a momentary switch to a toggle switch
- Counters
- Pattern generators
- ESD protection
- Modulo – n – counter
- Divide a clock signal by 2 or 4
- Latch-up performance
