CD74ACT74E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 927.99329mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Number of Outputs | 4 |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 85MHz |
| Propagation Delay | 9.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 2.4 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 1 |
| fmax-Min | 85 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 85000000Hz |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74ACT74E Overview
The flip flop is packaged in 14-DIP (0.300, 7.62mm). As part of the package Tube, it is embedded. T flip flop uses Differentialas the output. There is a trigger configured with Positive Edge. It is mounted in the way of Through Hole. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. -55°C~125°C TAis the operating temperature. This electronic flip flop is of type D-Type. It belongs to the 74ACTseries of FPGAs. There should be no greater frequency than 85MHzon its output. A total of 14terminations have been recorded. D latch belongs to the 74ACT74 family. Power is provided by a 5V supply. JK flip flop input capacitance is 10pF farads. It belongs to the family of electronic devices known as ACT. This electronic part is mounted in the way of Through Hole. Basically, it is designed with a set of 14 pins. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Due to its superior flexibility, it uses 2 circuits. It runs on 5Vvolts of power. For high efficiency, the supply voltage should be set to 5V. Featuring the maximum design flexibility, it has an output current of 24mA . There are no output lines on the JK flip flop. This D latch consumes 4μA quiescent current at all.
CD74ACT74E Features
Tube package
74ACT series
14 pins
5V power supplies
CD74ACT74E Applications
There are a lot of Texas Instruments CD74ACT74E Flip Flops applications.
- Frequency division
- Count Modes
- Communications
- Data storage
- ATE
- Single Down Count-Control Line
- Buffered Clock
- Guaranteed simultaneous switching noise level
- Memory
- ESD protection
