CD74ACT74M96G4
| Parameters | |
|---|---|
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.58mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 85MHz |
| Pin Count | 14 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 24mA |
| Number of Bits | 1 |
| Propagation Delay | 9.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 2.4 ns |
CD74ACT74M96G4 Overview
The package is in the form of SOIC. A total of 2elements are present in it. There are 14 terminations,The D flip flop is powered by a voltage of 5V . In terms of electronic devices, this device belongs to the ACTfamily of devices. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 14. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. An electronic part with 1bits has been designed. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. A total of 5V power supplies are needed to run it. For high efficiency, the supply voltage should be set to 5V. It is reported that there are 1 input lines. Despite external influences, it consumes 4μAof quiescent current. High level output current is set to -24mA. It is set to 24mAfor low level output current. Operating temperatures should be lower than 125°C. Ideally, the operating temperature should be greater than -55°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum supply voltage of 5.5V. This frequency can be achieved at 85MHz. It adopts a logic IC of type D FLIP-FLOP. Currently, it is equipped with 2 functions . It has 14 pins. This flip flop features a maximum design flexibility due to its output current of 24mA.
CD74ACT74M96G4 Features
14 pins
1 Bits
5V power supplies
2 Functions
14 pin count
CD74ACT74M96G4 Applications
There are a lot of Texas Instruments CD74ACT74M96G4 Flip Flops applications.
- Individual Asynchronous Resets
- Cold spare funcion
- Computing
- Memory
- QML qualified product
- Computers
- Latch-up performance
- Synchronous counter
- Shift registers
- Patented noise
