CD74FCT273M96G4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 70MHz |
| Propagation Delay | 7 ns |
| Turn On Delay Time | 7 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 15mA 48mA |
| Max Propagation Delay @ V, Max CL | 7ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 8 |
| fmax-Min | 70 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
CD74FCT273M96G4 Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). You can find it in the Tape & Reel (TR)package. There is a Non-Invertedoutput configured with it. This trigger uses the value Positive Edge. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.75V~5.25V. Currently, the operating temperature is 0°C~70°C TA. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74FCTseries FPGA. This D flip flop should not have a frequency greater than 70MHz. A total of 1elements are contained within it. There is a consumption of 8μAof quiescent energy. A total of 20terminations have been recorded. This D latch belongs to the family of 74FCT273. The D flip flop is powered by a voltage of 5V . Input capacitance of this device is 10pF farads. An electronic device belonging to the family FCTcan be found here. This electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. In this device, the clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. It is designed with a number of bits of 8. As soon as 5.25Vis reached, Vsup reaches its maximum value. Normal operation requires a supply voltage (Vsup) above 4.75V. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The power supply is 5V. There are 8 output lines on it.
CD74FCT273M96G4 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CD74FCT273M96G4 Applications
There are a lot of Texas Instruments CD74FCT273M96G4 Flip Flops applications.
- Data transfer
- Modulo – n – counter
- Asynchronous counter
- ATE
- Safety Clamp
- Power down protection
- Automotive
- Matched Rise and Fall
- Count Modes
- Bounce elimination switch
