CD74HC173PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | WITH DUAL OUTPUT ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC173 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 7.8mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.0078 A |
| Max Propagation Delay @ V, Max CL | 34ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 60 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HC173PWR Overview
The item is packaged in 16-TSSOP (0.173, 4.40mm Width)cases. You can find it in the Cut Tape (CT)package. The output it is configured with uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. Surface Mountmounts this electrical part. The supply voltage is set to 2V~6V. It is operating at a temperature of -55°C~125°C TA. This D latch has the type D-Type. This type of FPGA is a part of the 74HC series. A frequency of 60MHzshould be the maximum output frequency. In total, it contains 1 elements. The number of terminations is 16. D latch belongs to the 74HC173 family. It is powered from a supply voltage of 4.5V. Its input capacitance is 10pF farads. Devices in the HC/UHfamily are electronic devices. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 16pins on it. In this device, the clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. An electronic part with 4bits has been designed. Vsup reaches its maximum value at 6V. Normally, the supply voltage (Vsup) should be kept above 2V. Its superior flexibility is attributed to its use of 4 circuits. In light of its reliable performance, this T flip flop is well suited for TR. Its output current of 7.8mAallows for maximum design flexibility. There are 3 output lines in this JK flip flop. It has 2lines. There is 8μA quiescent current consumption by it. As an additional reference, you may refer to electronic flip flop WITH DUAL OUTPUT ENABLE.
CD74HC173PWR Features
Cut Tape (CT) package
74HC series
16 pins
4 Bits
CD74HC173PWR Applications
There are a lot of Texas Instruments CD74HC173PWR Flip Flops applications.
- Reduced system switching noise
- Memory
- Balanced Propagation Delays
- Safety Clamp
- Computing
- Control circuits
- Frequency Divider circuits
- Storage registers
- Convert a momentary switch to a toggle switch
- Dynamic threshold performance
