CD74HC377M
| Parameters | |
|---|---|
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latch |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 175 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.0052 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 53 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 8 |
| fmax-Min | 23 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
CD74HC377M Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. As part of the package Tube, it is embedded. In the configuration, Non-Invertedis used as the output. The trigger configured with it uses Positive Edge. The electronic part is mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. A temperature of -55°C~125°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. Its output frequency should not exceed 60MHz. A total of 1elements are present in it. There have been 20 terminations. The 74HC377 family contains it. A voltage of 5V is used as the power supply for this D latch. This JK flip flop has a 10pFfarad input capacitance. It belongs to the family of electronic devices known as HC/UH. There is an electronic part mounted in the way of Surface Mount. 20pins are included in its design. This device has the clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latch. This flip flop is designed with 8 Bits. There is a 6Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 2V. The system runs on a power supply of 2/6V watts. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. There are 8 output lines in this JK flip flop. There is 8μA quiescent current consumption by it. As an additional reference, you may refer to electronic flip flop WITH HOLD MODE. A total of 8 channels are available.
CD74HC377M Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC377M Applications
There are a lot of Texas Instruments CD74HC377M Flip Flops applications.
- Differential Individual
- Safety Clamp
- Registers
- Frequency Divider circuits
- Data storage
- Parallel data storage
- Pattern generators
- Guaranteed simultaneous switching noise level
- Digital electronics systems
- Shift Registers
