CD74HC377PWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 175 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.0052 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 53 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Input Lines | 8 |
| fmax-Min | 23 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC377PWG4 Overview
The flip flop is packaged in 20-TSSOP (0.173, 4.40mm Width). Package Tubeembeds it. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. It operates with a supply voltage of 2V~6V. It is operating at -55°C~125°C TA. D-Typeis the type of this D latch. This type of FPGA is a part of the 74HC series. There should be no greater frequency than 60MHzon its output. In total, it contains 1 elements. It has been determined that there have been 20 terminations. You can search similar parts based on 74HC377. An input voltage of 5Vpowers the D latch. Input capacitance of this device is 10pF farads. Electronic devices of this type belong to the HC/UHfamily. This electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. There is a clock edge trigger type of Positive Edgeon this device. There is a FF/Latchesbase part number assigned to the RS flip flops. It is designed with a number of bits of 8. In this case, the maximum supply voltage (Vsup) reaches 6V. A normal operating voltage (Vsup) should remain above 2V. It operates from 2/6V power supplies. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. This input has 8lines. As a result, it consumes 8μA of quiescent current without being affected by external factors. There is also a characteristic of WITH HOLD MODE.
CD74HC377PWG4 Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC377PWG4 Applications
There are a lot of Texas Instruments CD74HC377PWG4 Flip Flops applications.
- Control circuits
- Differential Individual
- ESD performance
- Load Control
- Bus hold
- Reduced system switching noise
- ATE
- Data transfer
- Event Detectors
- Common Clocks
