CD74HC377PWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Propagation Delay | 175 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.0052 A |
| Number of Bits per Element | 8 |
| Prop. Delay@Nom-Sup | 53 ns |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| fmax-Min | 23 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HC377PWRG4 Overview
In the form of TSSOP, it has been packaged. The package Tape & Reel (TR)contains it. The list contains 1 elements. Currently, there are 20 terminations. It is powered from a supply voltage of 5V. The electronic device belongs to the HC/UHfamily. A part of the electronic system is mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. The part is included in FF/Latches. This D flip flop is well suited for TR based on its reliable performance. Quiescent current is consumed by the D latch in the amount of 8μA. Additionally, it is characterized by WITH HOLD MODE. A -5.2mAis set for the high level output current. There is no low level output current set at 5.2mA. It is recommended that the operating temperature be below 125°C. A temperature above -55°Cshould be used for the operation. In order for it to operate, a supply voltage of 2Vis required. It is capable of supporting a maximum supply voltage of 6V. It is possible to obtain a frequency of 60MHz. The logic IC it uses is D FLIP-FLOP. As a result, it is equipped with 1 functions . With 20 pins, it is equipped with a low power consumption. As a result of its output current of 5.2mA, it is very flexible in terms of design.
CD74HC377PWRG4 Features
Tape & Reel (TR) package
20 pins
1 Functions
20 pin count
CD74HC377PWRG4 Applications
There are a lot of Texas Instruments CD74HC377PWRG4 Flip Flops applications.
- Shift Registers
- Instrumentation
- Circuit Design
- Memory
- Load Control
- Test & Measurement
- Registers
- Convert a momentary switch to a toggle switch
- Divide a clock signal by 2 or 4
- Frequency Divider circuits
