banner_page

CD74HCT173E

4.5V~5.5V 60MHz 4 Bit D-Type Flip Flop DUAL 74HCT173 16 Pins 8μA 74HCT Series 16-DIP (0.300, 7.62mm)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-CD74HCT173E
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: -
  • Stock: 602
  • Description: 4.5V~5.5V 60MHz 4 Bit D-Type Flip Flop DUAL 74HCT173 16 Pins 8μA 74HCT Series 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 2 days ago)
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Weight 951.693491mg
Operating Temperature -55°C~125°C TA
Packaging Tube
Series 74HCT
JESD-609 Code e4
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Type D-Type
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Additional Feature WITH DUAL OUTPUT ENABLE
Subcategory FF/Latches
Technology CMOS
Voltage - Supply 4.5V~5.5V
Terminal Position DUAL
Peak Reflow Temperature (Cel) NOT SPECIFIED
Supply Voltage 5V
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number 74HCT173
Function Master Reset
Qualification Status Not Qualified
Output Type Tri-State, Non-Inverted
Operating Supply Voltage 5V
Number of Elements 1
Polarity Non-Inverting
Power Supplies 5V
Number of Circuits 4
Load Capacitance 50pF
Output Current 7.8mA
Number of Bits 4
Clock Frequency 60MHz
Propagation Delay 40 ns
Turn On Delay Time 17 ns
Family HCT
Logic Function D-Type, Flip-Flop
Current - Quiescent (Iq) 8μA
Current - Output High, Low 6mA 6mA
Max I(ol) 0.006 A
Max Propagation Delay @ V, Max CL 40ns @ 4.5V, 50pF
Trigger Type Positive Edge
Input Capacitance 10pF
Power Supply Current-Max (ICC) 0.08mA
Number of Output Lines 3
Clock Edge Trigger Type Positive Edge
Height 5.08mm
Length 19.3mm
Width 6.35mm
Thickness 3.9mm
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

CD74HCT173E Overview


The flip flop is packaged in a case of 16-DIP (0.300, 7.62mm). It is included in the package Tube. It is configured with Tri-State, Non-Invertedas an output. It is configured with a trigger that uses a value of Positive Edge. Through Holemounts this electrical part. The JK flip flop operates at a voltage of 4.5V~5.5V. It is operating at -55°C~125°C TA. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74HCT series. It should not exceed 60MHzin terms of its output frequency. D latch consists of 1 elements. During its operation, it consumes 8μA quiescent energy. It has been determined that there have been 16 terminations. This D latch belongs to the family of 74HCT173. The power source is powered by 5V. Its input capacitance is 10pF farads. Devices in the HCTfamily are electronic devices. There is an electronic component mounted in the way of Through Hole. 16pins are included in its design. It has a clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. 4bits are used in its design. Its flexibility is enhanced by 4 circuits. There are 5V power supplies attached to it. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. This T flip flop features a maximum design flexibility due to its output current of 7.8mA. To operate, the chip has a total of 3 output lines. Additionally, there are WITH DUAL OUTPUT ENABLE on the electronic flip flop that can be referred to.

CD74HCT173E Features


Tube package
74HCT series
16 pins
4 Bits
5V power supplies

CD74HCT173E Applications


There are a lot of Texas Instruments CD74HCT173E Flip Flops applications.

  • Guaranteed simultaneous switching noise level
  • Frequency division
  • Parallel data storage
  • Consumer
  • EMI reduction circuitry
  • 2 – Bit synchronous counter
  • Computers
  • Single Up Count-Control Line
  • Synchronous counter
  • Memory

Write a review

Note: HTML is not translated!
    Bad           Good