CD74HCT175E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latch |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74HCT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 4mA |
| Number of Bits | 4 |
| Clock Frequency | 25MHz |
| Propagation Delay | 53 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 4mA |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT175E Overview
The flip flop is packaged in 16-DIP (0.300, 7.62mm). You can find it in the Tubepackage. It is configured with Differentialas an output. It is configured with a trigger that uses a value of Positive Edge. There is an electrical part that is mounted in the way of Through Hole. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is operating at a temperature of -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. You should not exceed 25MHzin the output frequency of the device. The element count is 1 . Terminations are 16. The 74HCT175 family contains it. It is powered from a supply voltage of 5V. Its input capacitance is 10pF farads. It is a member of the HCTfamily of D flip flop. A part of the electronic system is mounted in the way of Through Hole. This board is designed with 16pins on it. Its clock edge trigger type is Positive Edge. There is a FF/Latchbase part number assigned to the RS flip flops. An electronic part designed with 4bits is used in this application. 4 circuits are used to achieve its superior flexibility. A total of 5V power supplies are needed to run it. For high efficiency, the supply voltage should be set to 5V. This T flip flop features a maximum design flexibility due to its output current of 4mA. There is a consumption of 8μAof quiescent current from it.
CD74HCT175E Features
Tube package
74HCT series
16 pins
4 Bits
5V power supplies
CD74HCT175E Applications
There are a lot of Texas Instruments CD74HCT175E Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- Balanced 24 mA output drivers
- Cold spare funcion
- Individual Asynchronous Resets
- Patented noise
- Data transfer
- Pattern generators
- Frequency division
- Data Synchronizers
- Buffer registers
