CD74HCT377M
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latch |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 4mA |
| Number of Bits | 8 |
| Clock Frequency | 50MHz |
| Propagation Delay | 57 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 16 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 38ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT377M Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). A package named Tubeincludes it. As configured, the output uses Non-Inverted. This trigger is configured to use Positive Edge. It is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. -55°C~125°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. It belongs to the 74HCTseries of FPGAs. Its output frequency should not exceed 50MHz Hz. In total, it contains 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. This D latch belongs to the family of 74HCT377. The power source is powered by 5V. The input capacitance of this JK flip flopis 10pF farads. It is a member of the HCTfamily of D flip flop. There is an electronic component mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. It has a clock edge trigger type of Positive Edge. This device is part of the FF/Latchbase part number family. There are 8bits in this flip flop. A total of 5V power supplies are needed to run it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. With an output current of 4mA, this device offers maximum design flexibility. There are 3 output lines on it. Despite external influences, it consumes 8μAof quiescent current. In addition, WITH HOLD MODEis a characteristic of it. 8is the number of channels.
CD74HCT377M Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
CD74HCT377M Applications
There are a lot of Texas Instruments CD74HCT377M Flip Flops applications.
- Latch-up performance
- Functionally equivalent to the MC10/100EL29
- Memory
- Buffer registers
- Frequency Dividers
- 2 – Bit synchronous counter
- Computers
- Buffered Clock
- Single Down Count-Control Line
- Count Modes
