DM74ALS576AWM
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 30MHz |
| Base Part Number | 74ALS576 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 4 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 18mA |
| Current - Output High, Low | 2.6mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 14ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -2.6mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DM74ALS576AWM Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. D flip flop is included in the Tubepackage. This output is configured with Tri-State, Inverted. It is configured with the trigger Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. A temperature of 0°C~70°C TAis considered to be the operating temperature. D-Typeis the type of this D latch. It belongs to the 74ALSseries of FPGAs. In order for it to function properly, its output frequency should not exceed 30MHz. A total of 1elements are present in it. During its operation, it consumes 18mA quiescent energy. The 74ALS576 family contains this object. There is an electronic part mounted in the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is designed with a number of bits of 8. The superior flexibility is achieved through the use of 8 circuits. For high efficiency, the supply voltage should be set to 5V. It has 3 output lines to operate. It has 8lines. There is -2.6mA output current at the high level. There is no low level output current set at 24mA. A temperature below 70°Cshould be used for operation. A temperature above 0°Cshould be used for the operation. Despite its minimal supply voltage of 4.5V, it is capable of operating. It is capable of supporting a maximum supply voltage of 5.5V. This frequency can be achieved at 30MHz.
DM74ALS576AWM Features
Tube package
74ALS series
20 pins
8 Bits
DM74ALS576AWM Applications
There are a lot of ON Semiconductor DM74ALS576AWM Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Divide a clock signal by 2 or 4
- Latch
- Circuit Design
- CMOS Process
- Single Down Count-Control Line
- Reduced system switching noise
- Shift Registers
- Common Clocks
- Data Synchronizers
