E-L6910
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Frequency | 1MHz |
| Base Part Number | L6910 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 913mV |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 12V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1.3A |
| Voltage - Supply (Vcc/Vdd) | 5V~12V |
| Control Features | Current Limit, Frequency Control, Phase Control, Power Good, Soft Start |
| Input Voltage (Min) | 5V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 100% |
| Clock Sync | No |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
E-L6910 Overview
The switching controller fits in the 16-SOIC (0.154, 3.90mm Width) package and is ideal for most applications. For 1 outputs, the dc motor controller is appropriate. Tube is the solid enclosure in which PMIC is packaged. Transistor Driver dc switching's outputs (s) are supported. dc control's supply and operating voltages are 5V~12V. Suitable for a -40°C~150°C TJ dc switcher. It can switch at 200kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Featured in the dcdc regulator is Current Limit, Frequency Control, Phase Control, Power Good, Soft Start which allows efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. DUAL are the position of the terminal of the switching converters. An array of 16 terminations of dc switching. It includes PULSE WIDTH MODULATION as one of the control techniques dc dc converter ic adapts. 12V nominal DC switcher's voltage input. A search for "L6910" will reveal other relevant dc to dc converter ics. 16 pins are present on switching converter. This dc dc voltage regulator should be powered by a voltage of 5V. A 913mV voltage of DC regulator was detected in the test statistics. It's important to remember that the dc dc regulator's normaloutput current is 1.3A, so you should note it down when starting a new project. As DC switcher has a Surface Mount, it's suitable for most applications and prototype designs. There is 1MHz frequency setting on the switching controller. To run the voltage regulator dc to dc safely and reliably, users should apply 12V to the voltage regulator dc to dc.
E-L6910 Features
Transistor Driver Outputs
Switching Frequency: 200kHz
Current Limit, Frequency Control, Phase Control, Power Good, Soft Start
PULSE WIDTH MODULATION
Frequency: 1MHz
E-L6910 Applications
There are a lot of STMicroelectronics E-L6910 DC to DC converter applications.
- Hydraulic presses
- Window air conditioners
- Household control circuits
- Sensitive electronic devices
- Electrical distribution systems
- Smoke prevention equipment
- Laboratories
- Hydrogen power
- Network technology
- Solar power plants
