HEF4013BTT,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 4000B |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 3V~15V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 4013 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 2 |
| Clock Frequency | 40MHz |
| Propagation Delay | 220 ns |
| Turn On Delay Time | 30 ns |
| Logic Function | AND, D-Type |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 3.4mA 3.4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 60ns @ 15V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
HEF4013BTT,118 Overview
The flip flop is packaged in 14-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop uses Differentialas its output configuration. The trigger configured with it uses Positive Edge. It is mounted in the way of Surface Mount. With a supply voltage of 3V~15V volts, it operates. It is at -40°C~125°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. In this case, it is a type of FPGA belonging to the 4000B series. You should not exceed 40MHzin its output frequency. It consumes 4μA of quiescent current without being affected by external factors. A total of 14 terminations have been made. JK flip flop belongs to 4013 family. The power supply voltage is 5V. A JK flip flop with a 7.5pFfarad input capacitance is used here. It is mounted in the way of Surface Mount. Basically, it is designed with a set of 14 pins. This device has Positive Edgeas its clock edge trigger type. For normal operation, the supply voltage (Vsup) should be kept above 3V. The superior flexibility of this circuit is achieved by using 2 circuits. There are no output lines on the JK flip flop.
HEF4013BTT,118 Features
Tape & Reel (TR) package
4000B series
14 pins
HEF4013BTT,118 Applications
There are a lot of Nexperia USA Inc. HEF4013BTT,118 Flip Flops applications.
- Latch
- Reduced system switching noise
- Consumer
- ESD protection
- Single Down Count-Control Line
- Bounce elimination switch
- Common Clocks
- Buffered Clock
- Count Modes
- Matched Rise and Fall
