IDT74FCT823CTSOG8
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 24 |
| Packaging | Tape and Reel |
| Published | 2006 |
| JESD-609 Code | e3 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 24 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 9 |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 1.5 ns |
| Family | FCT |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.048 A |
| Prop. Delay@Nom-Sup | 6 ns |
| High Level Output Current | 48mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 83300000Hz |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
IDT74FCT823CTSOG8 Overview
SOICis the packaging method. You can find it in the Tape and Reelpackage. A total of 1elements are present in it. There are 24 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. A voltage of 5V provides power to the D latch. It belongs to the family of electronic devices known as FCT. There is an electronic component mounted in the way of Surface Mount. This board is designed with 24pins on it. Its clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. The flip flop is designed with 9bits. A total of 5V power supplies are needed to run it. The flip flop has 2embedded ports. High efficiency requires the supply voltage to be maintained at 5V. It is set to 48mAfor the high level output current. There is no low level output current set at 15mA. It is recommended that the operating temperature be lower than 85°C. Temperatures above -40°Cshould be used. Initially, it requires a voltage of 4.75V as the minimum supply voltage. There is a maximum supply voltage of 5.25V. This logic IC is BUS DRIVER. The T flip flop is equipped with 1functions . The JK flip flop has a pin count of 24.
IDT74FCT823CTSOG8 Features
Tape and Reel package
24 pins
9 Bits
5V power supplies
1 Functions
24 pin count
IDT74FCT823CTSOG8 Applications
There are a lot of Integrated Device Technology (IDT) IDT74FCT823CTSOG8 Flip Flops applications.
- Supports Live Insertion
- Consumer
- Bus hold
- Functionally equivalent to the MC10/100EL29
- Computing
- Buffered Clock
- Balanced 24 mA output drivers
- Bounce elimination switch
- Memory
- Buffer registers
