LT1510IS#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Power Management Circuits |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 16V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1510 |
| Pin Count | 16 |
| Output Voltage | 20V |
| Input Voltage-Nom | 16V |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 7V |
| Analog IC - Other Type | BATTERY CHARGE CONTROLLER |
| Output Current | 1.5A |
| Min Input Voltage | 7V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 29V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 4.5mA |
| Nominal Input Voltage | 28V |
| Switcher Configuration | SINGLE |
| Switching Frequency-Max | 200kHz |
| Fault Protection | Over Voltage |
| Battery Chemistry | Multi-Chemistry |
| Current - Charging | Constant - Programmable |
| Charge Current - Max | 1.5A |
| Battery Pack Voltage | 20V Max |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1510IS#PBF Overview
There is a package named Tube that contains it.It comes as part of the 16-SOIC (0.154, 3.90mm Width) package.This device has a mounting type of Surface Mount.Keeping the temperature at -40°C~85°C TA is the right choice.To operate the device, an analog IC called BATTERY CHARGE CONTROLLER is used.The device cannot be charged without Constant - Programmable current flowing through it.If you use the base part number LT1510, you can look for related parts.Among its terminations, there are 16.The battery pack has 20V Max.Due to the 16 pins on it, it is a very simple circuit.In terms of maximum charging current, it is rated at 1.5A.You need 16 pins for it to work.A battery with 0V would be enough for it to run.There is no damage to the device if an input voltage of 30V is applied.With a 20V output voltage, high efficiency is possible.It is in this instance that the device's output current is set to 1.5A.The device falls under the Power Management Circuits subcategory.The device can operate at as low a supply voltage as possible, such as 7V.Vsup (maximum supply voltage) is set in the command to 4.5mA.Input voltage minimum is 7V volts, which is a requirement of the device.The device has 16V voltage input at the moment.It can accept a maximum input voltage of 29V volts.The part's switching frequency is at most 200kHz.
LT1510IS#PBF Features
Battery pack voltage of 20V Max
Power Management Circuits subcategory
16-SOIC (0.154, 3.90mm Width) package
LT1510IS#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1510IS#PBF Battery Chargers ICs applications.
- Automotive/electrical vehicle
- Drone
- Laptops
- USB power delivery (USB-C) devices
- Automotive electronics
- High end, feature-rich consumer
- Medical
- Military equipment
- Mobile router
- MP3, MP4 player
