LTC3728LEUH-1#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 32-WFQFN Exposed Pad |
| Number of Pins | 32 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 32 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC3728 |
| Function | Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 7V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Number of Channels | 1 |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 3A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~28V |
| Control Features | Enable, Power Good, Soft Start |
| Input Voltage (Min) | 4.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 260kHz~550kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PHASE-SHIFT |
| Max Frequency | 590kHz |
| Duty Cycle (Max) | 99.4% |
| Clock Sync | No |
| Height | 750μm |
| Length | 5mm |
| Width | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC3728LEUH-1#PBF Overview
With a 32-WFQFN Exposed Pad package, the switching controller is suitable for a wide range of applications. For 2 outputs, the dc motor controller is appropriate. The pmic is packaged in Tube solid enclosure. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching'sdc control's supply and operating voltages are 4.5V~28V. Suitable for work in a -40°C~85°C TA dc switcher. Using this switching controller, it is possible to switch at 260kHz~550kHz. The Surface Mount value makes it suitable for general dc dc regulator. For efficient switching control, the dcdc regulator features Enable, Power Good, Soft Start. An analog IC DUAL SWITCHING CONTROLLER is connected to the switch converters. Switching converters are designed with the terminal (s) at position QUAD . A variety of 32 terminations are available in dc switching. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. 15V nominal DC switcher's voltage input. You can find other relevant dc to dc converter ics by searching "LTC3728". There are 32 pins on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. dc dc voltage regulators should have a minimum input voltage of 4.5V. Statistically, DC regulator outputs 7V volts. It's important to remember that the dc dc regulator's normaloutput current is 3A, so you should note it down when starting a new project. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. DC regulator's maximum frequency is 590kHz. Communication with high quality requires 1 channels.
LTC3728LEUH-1#PBF Features
Transistor Driver Outputs
Switching Frequency: 260kHz~550kHz
Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
LTC3728LEUH-1#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC3728LEUH-1#PBF DC to DC converter applications.
- Overvoltage protection circuits in TV sets
- Servo drive system
- Laboratories
- Motor controller circuits
- CMM
- Bending machines
- Wind power
- Constant current circuits
- Program control systems
- Current source circuits
