M74HC174B1R
| Parameters | |
|---|---|
| Base Part Number | M74HC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 6 |
| Clock Frequency | 66MHz |
| Propagation Delay | 220 ns |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 23ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 6 |
| fmax-Min | 28 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Height | 5.1mm |
| Length | 20mm |
| Width | 12.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 4.535924g |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 4.5V |
| Terminal Pitch | 2.54mm |
M74HC174B1R Overview
In the form of 16-DIP (0.300, 7.62mm), it has been packaged. Package Tubeembeds it. This output is configured with Non-Inverted. JK flip flop uses Positive Edgeas the trigger. In this case, the electronic component is mounted in the way of Through Hole. A 2V~6Vsupply voltage is required for it to operate. It is at -55°C~125°C TAdegrees Celsius that the system is operating. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74HC series. In order for it to function properly, its output frequency should not exceed 66MHz. A total of 1elements are contained within it. As a result, it consumes 4μA of quiescent current without being affected by external factors. In 16terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Members of the M74HC174family make up this object. It is powered by a voltage of 4.5V . Its input capacitance is 5pFfarads. Devices in the HC/UHfamily are electronic devices. It is mounted in the way of Through Hole. Basically, it is designed with a set of 16 pins. It has a clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. There are 6bits in its design. In this case, the maximum supply voltage (Vsup) reaches 6V. For normal operation, the supply voltage (Vsup) should be above 2V. Its flexibility is enhanced by 7 circuits. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. It has 6lines.
M74HC174B1R Features
Tube package
74HC series
16 pins
6 Bits
M74HC174B1R Applications
There are a lot of STMicroelectronics M74HC174B1R Flip Flops applications.
- Frequency Divider circuits
- Asynchronous counter
- Storage Registers
- Matched Rise and Fall
- Data storage
- Digital electronics systems
- ESCC
- Single Down Count-Control Line
- Guaranteed simultaneous switching noise level
- Count Modes
