M74HC273B1R
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | Through Hole |
| Type | D-Type |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 4.5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | M74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Power Dissipation | 500mW |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 66MHz |
| Propagation Delay | 240 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 3.93mm |
| Length | 25.4mm |
| Width | 7.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC273B1R Overview
The package is in the form of 20-DIP (0.300, 7.62mm). It is contained within the Tubepackage. As configured, the output uses Non-Inverted. This trigger uses the value Positive Edge. Through Holeis occupied by this electronic component. A voltage of 2V~6Vis used as the supply voltage. -55°C~125°C TAis the operating temperature. D-Typeis the type of this D latch. It is a type of FPGA belonging to the 74HC series. In order for it to function properly, its output frequency should not exceed 66MHz. D latch consists of 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. A total of 20 terminations have been made. JK flip flop belongs to M74HC273 family. A voltage of 4.5V is used to power it. JK flip flop input capacitance is 5pF farads. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. It is mounted by the way of Through Hole. The 20pins are designed into the board. This device exhibits a clock edge trigger type of Positive Edge. This part is included in FF/Latches. This flip flop is designed with 8 Bits. It reaches the maximum supply voltage (Vsup) at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. To achieve this superior flexibility, 8 circuits are used. An electrical current of 2/6V volts is applied to it. This T flip flop features a maximum design flexibility due to its output current of 5.2mA.
M74HC273B1R Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC273B1R Applications
There are a lot of STMicroelectronics M74HC273B1R Flip Flops applications.
- QML qualified product
- Set-reset capability
- EMI reduction circuitry
- Asynchronous counter
- Registers
- Test & Measurement
- Guaranteed simultaneous switching noise level
- Counters
- Single Down Count-Control Line
- Individual Asynchronous Resets
