MAX15001AEUB+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX15001 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 9.5V~24V |
| Control Features | Enable |
| Input Voltage (Min) | 9.5V |
| Topology | Boost, Flyback |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 25kHz~625kHz |
| Input Voltage (Max) | 24V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Max Frequency | 2.5MHz |
| Max Duty Cycle | 50 % |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX15001AEUB+ Overview
Capsuled in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package, the switching controller suits most application needs. For outputs of 1, this dc motor controller is suitable. There is a Tube solid enclosure around the pmic. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching's9.5V~24V is the supply voltage and the operating voltage of the dc control. Workable in an dc switcher where -40°C~85°C TA is the -40°C~85°C TArm. With this switching controller, you can switch at 25kHz~625kHz. dc dc regulator can be generalized using Surface Mount. Featured in the dcdc regulator is Enable which allows efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. switching converters terminal (s) are designed to be at DUAL. The 10 terminations can be used for a wide range of dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. The nominal DC switcher's voltage input is 12V. Searching "MAX15001" will return other relevant dc to dc converter ics. There are 10 pins on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. It is recommended to use 9.5V as the minimum input voltage of dc dc voltage regulator. The dc to dc regulator is limited to 24V input voltage. A starting point for a project is to note down the dc dc regulator's usual output current, which is 1A. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 50 %. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. DC regulator's maximum frequency is 2.5MHz.
MAX15001AEUB+ Features
Transistor Driver Outputs
Switching Frequency: 25kHz~625kHz
Enable
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
MAX15001AEUB+ Applications
There are a lot of Maxim Integrated MAX15001AEUB+ DC to DC converter applications.
- Network technology
- Smart grid
- Printing
- Solar power plants
- Experimental setup
- Photovoltaic power
- Drilling machines
- Die casting equipment
- Game consoles
- Printing equipment
