MC100E131FNR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Operating Temperature | 0°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 100E |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100E131 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Number of Circuits | 4 |
| Number of Bits | 4 |
| Clock Frequency | 1.4GHz |
| Propagation Delay | 675 ps |
| Turn On Delay Time | 500 ps |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 70mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC100E131FNR2 Overview
The flip flop is packaged in a case of 28-LCC (J-Lead). Package Tape & Reel (TR)embeds it. In the configuration, Differentialis used as the output. JK flip flop uses Positive Edgeas the trigger. Surface Mountmounts this electrical part. A voltage of -4.2V~-5.7Vis used as the supply voltage. The operating temperature is 0°C~85°C TA. This electronic flip flop is of type D-Type. In this case, it is a type of FPGA belonging to the 100E series. This D flip flop should not have a frequency greater than 1.4GHz. A total of 1 elements are present. It consumes 70mA of quiescent 28terminations have occurred. D latch belongs to the 100E131 family. The D flip flop is powered by a voltage of 5V . A part of the electronic system is mounted in the way of Surface Mount. There are 28pins on it. This device's clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part designed with 4bits is used in this application. It reaches 5.7Vwhen the maximum supply voltage (Vsup) is applied. Despite its superior flexibility, it relies on 4 circuits to achieve it. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. A high level output current of 50mAis set. In the low level output current setting, 50mAis used.
MC100E131FNR2 Features
Tape & Reel (TR) package
100E series
28 pins
4 Bits
MC100E131FNR2 Applications
There are a lot of ON Semiconductor MC100E131FNR2 Flip Flops applications.
- CMOS Process
- Safety Clamp
- Data Synchronizers
- Latch
- Counters
- Data storage
- Computers
- Bus hold
- Pattern generators
- Control circuits
