MC100E451FNR2
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100E451 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Number of Circuits | 2 |
| Clock Frequency | 1.1GHz |
| Propagation Delay | 1.05 ns |
| Turn On Delay Time | 625 ps |
| Current - Quiescent (Iq) | 101mA |
| Output Characteristics | OPEN-EMITTER |
| Number of Bits per Element | 6 |
| Trigger Type | Positive Edge |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.57mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Operating Temperature | 0°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 100E |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 240 |
MC100E451FNR2 Overview
28-LCC (J-Lead)is the way it is packaged. As part of the package Tape & Reel (TR), it is embedded. As configured, the output uses Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. The supply voltage is set to -4.2V~-5.7V. The operating temperature is 0°C~85°C TA. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 100E series. A frequency of 1.1GHzshould not be exceeded by its output. The element count is 1 . T flip flop consumes 101mA quiescent energy. Terminations are 28. D latch belongs to the 100E451 family. A voltage of 5V is used to power it. A part of the electronic system is mounted in the way of Surface Mount. This board has 28 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The maximal supply voltage (Vsup) reaches 5.7V. In order to achieve its superior flexibility, 2 circuits are used. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. There are -4.5V power supplies attached to it.
MC100E451FNR2 Features
Tape & Reel (TR) package
100E series
28 pins
-4.5V power supplies
MC100E451FNR2 Applications
There are a lot of ON Semiconductor MC100E451FNR2 Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Computing
- Buffered Clock
- Frequency Divider circuits
- Differential Individual
- Control circuits
- Common Clocks
- Event Detectors
- Storage Registers
- Data storage
